Nothing makes a pair of handmade earrings more personable than a handmade earring display card to hold and display them. Sure you can put your earrings in a small jewelry box with cotton batting - but that just feels so "department store" and so much less special. Why not add the extra touch of a handmade accessory for your accessory? Follow the instructions below to see how easy it is to add that special flare to a pair of handmade earrings.*The earrings shown in this image are The John Payne and are some of my personal favorites. As always, you can find my collection online at http://LOVELiNSY.etsy.com.
1. Cut two pieces of cardstock to the appropriate size - here I have cut the larger of the two pieces (black) to 2.5" x 3.75" and the smaller of the two pieces (white) to 2.25" x 3.5". I find using two pieces makes the finished product much more sturdy than a single sheet of cardstock. Here I have used the classic combination of black and white, but you may choose any color of the rainbow. Further, I choose to cut them to slightly different sizes and let one act as a border; you may choose to cut them to the same size, however.
2. Once cut, take your top piece and stamp a design using a rubber stamp and a pigment ink pad - check for "Embossing is optional" on the back to make sure the ink can be embossed. Before the ink dries, sprinkle your embossing powder over the stamp design and gently shake the excess powder onto a clean sheet of paper that you can later use to funnel the powder back into the container (same as you would glitter). Here, I have used Stampabilities Pigment Ink in Bright Pink and Stampendous Stamp-N-Stuff Embossing Powder in Translucent White Pearl.
Using your embossing tool, emboss the design until it becomes 3-D and has a soft, puffy look. (Below, the picture on the right shows the progression of the ink as it becomes embossed. Towards the rear, the ink that appears shiny and has a glare has been fully embossed, while that in the front which is darker and grainier has not been fully embossed.) I use the Marvy Embossing Heat Tool (Model 2500). Be careful with the embossing tool, however - they get EXTREMELY HOT and can burn your skin and cause burn marks on the paper if left in the same area for too long. To avoid such burn marks on your paper, do NOT concentrate on one area at a time and instead move the embossing tool around in a circular motion. To avoid burning yourself, never touch the head of the tool and never lave the tool on unattended.
4. Using a pushpin, mark four holes. In my examples I have marked holes in the following manner: The first set of holes is marked in the upper corners at 5/16" in (from the edge and the top) of the largest piece of cardstock. The second set of holes is marked 3/4" from the sides and 5/8" from the top of the largest piece of cardstock. The first set of holes will be used as a guide for eyelets; the second set of holes will be left alone and is where the earring posts will hang. When making multiple earring display cards, I suggest marking a "guide card" with the holes and subsequently using it as a template for the rest; thereafter stacking other cards below the "guide card" and using its holes to quickly and efficiently mark those of the remaining cards below it.
5. Next you will put eyelets in the top holes of the card. Using the pin-holes from the top-most (first) set of holes as a marker, use an eyelet tool (or a hammer and punch) to make small holes for eyelets. Position your eyelets in the hole (flat side up) and use your eyelet tool (or anvil and hammer) to secure the eyelet in place.
7. With your pushpin, make sure the lower (second) set of holes is punched all the way through by punching from both sides. You will not need to do anything else to these holes, as this is where the earring posts will hang from.8. Finally, sign your name at the bottom and hang your earrings from your card!
I hope this helps spark your creativity so you can start making your very own handmade earring cards!
LOVE, LiNSY
No comments:
Post a Comment